Managing Equipment Collision and Run-Over Risks in an Open-Pit Mine

Case
19 November 2026 🇷🇺 Original language: русский

Project Background and the Shift to Objective In-Cab Monitoring

Operating heavy haulage equipment in open-pit mining involves two systemic risk factors: cumulative operator fatigue during month-long FIFO rotations and extensive blind spots around mining haul trucks. When a site lacks objective recording tools, traffic incident investigations rely on assumptions and circumstantial evidence, making it difficult to accurately eliminate root causes.

Evgeniy Likhachyov, Industrial Safety Director at Sibkor, examines the phased deployment of a comprehensive collision and run-over prevention system at an open-pit mine. The starting point was nine incidents involving BelAZ haul trucks between 2023 and 2025 caused by operators falling asleep or losing focus—including breaching a safety berm and striking a service vehicle during wheel maintenance. To stop operating blind, in December 2025 the mine equipped 41 haul trucks with an automated driver monitoring system (DMS) featuring in-cab operator state sensors and external dashcams.

The system detects eye closure, gaze distraction from the haul road, mobile phone use, smoking, and eating while driving. To avoid overwhelming the mine dispatcher with a constant stream of alerts, primary 24/7 monitoring is handled by an external dispatch center: an operator filters alerts according to an approved protocol and escalates only critical events to the mine site. Dedicated maintenance support keeps the onboard hardware running reliably in harsh pit conditions—in 2026 alone, technicians performed 1,044 remote health checks and resolved more than 250 tickets remotely alongside 375 on-site service calls. As a result, 100% of traffic incidents, fires, and premature component failures are now investigated using objective video evidence.

Workforce Pushback and the Sensor Calibration Challenge

Predictably, installing in-cab cameras met with resistance from operators who viewed the system as an invasion of privacy. Early on, drivers smeared grease over lenses, covered cameras with bottle caps and rags, tore out wiring, and unscrewed antennas. A combination of strict anti-tampering enforcement by supervisory and engineering staff and transparent communication during safety meetings turned the tide: only nine deliberate tampering incidents were recorded over the year, isolated cases became rare, and operators began proactively reporting camera malfunctions themselves.

Shift-change equipment calibration proved to be a tougher organizational hurdle. Because operators vary in height, the sensors must adjust to each driver's seating position; however, some personnel press the calibration button and pull away before the software finishes configuring. Until the workflow is fully automated, compliance is tracked manually: at the start of day and night shifts, vehicle status is verified remotely, and uncalibrated crews are contacted individually via the dispatcher, by phone, or over the two-way radio.

Blind Spot Protection and Reducing Alarm Fatigue

Operational experience showed that monitoring driver alertness alone does not prevent collisions during low-speed maneuvering. Two sideswipe incidents occurred at the mine—one involving a mobile canteen truck on a haul road to the working face, and another involving a loaded open-top railcar at a rail crossing. In both cases, the haul truck operators were awake and sober, but failed to spot the obstacle in a restricted-visibility zone.

To close this risk gap, industrial pilot testing of an intelligent surround-view and collision avoidance system was launched on two BelAZ trucks:

  • Tagless detection. Computer vision algorithms identify personnel and vehicles directly through optical cameras and highlight hazards on the in-cab display, eliminating issues with dead batteries, forgotten wearables, or swapped proximity tags.
  • Brake system integration. During a hazardous close call at speeds up to 10 km/h, the system automatically brings the haul truck to a stop; upcoming upgrades include interlocking vehicle launch and dump-body raising whenever an object is detected near the truck.
  • Cognitive and acoustic relief for operators. With a two-way radio, the Karyer fleet management system, fire suppression controls, overhead power line proximity alarms, and the DMS all running simultaneously in the cab, excessive audio alerts cause alarm fatigue by the end of a shift. Disabling audible chimes during testing in favor of automatically expanding the relevant camera feed to full screen upon gear selection preserved situational awareness without unnecessary noise and earned strong support from operators.

Unified Digital Platform and Video Analytics Potential

Scaling these solutions relies on robust connectivity: installing an additional LTE base station delivered 100% network coverage across the pit, eliminating blind spots where trucks previously dropped off the dispatcher's map. Looking ahead, Evgeniy Likhachyov notes that the DMS and collision avoidance modules will merge into a unified platform, shifting from punitive oversight to a digital coaching model that turns close calls into non-punitive, personalized operator training.

In parallel, the team is exploring ways to extend video analytics to adjacent operational challenges: geometric monitoring of off-center payload heaps in the dump body, geotagged detection of rock spillage on haul roads to prevent tire cuts, assessment of haul road width and safety berm height, wear monitoring on excavator bucket teeth, and verification of wheel chock placement and three-point contact compliance when operators descend cab ladders.

Key Takeaways from This Presentation

  • How to design an event-filtering protocol between an external 24/7 DMS monitoring center and the on-site mine dispatcher.
  • Proven methods to overcome in-cab camera tampering among rotational crews and achieve 100% sensor calibration compliance at shift handover.
  • How a tagless 360° collision avoidance system works and at what speeds automatic braking engages on a BelAZ haul truck.
  • Why excessive in-cab audio alerts undermine operator focus, and how to replace audible alarms without compromising safety.
  • Which open-pit mining and excavation operational risks can be monitored using existing onboard camera infrastructure.
For Pro and VIP members
Structured summary with budget, timelines, team, and tools.
Choose plan

600+ cases and practices

Explore the full library of industrial safety best practices

Go to library
We use cookies to improve your experience · Cookie Notice

Join the leaders

14,000+ professionals · 128+ countries

1
Contacts
2
Profile

Registration

Tell us about yourself

Required field
Required field
Enter a valid email
Invalid number

Registration

Professional details

Required field
Required field
Required field

Please consent to newsletters. This will greatly enhance your platform experience.

Registration complete

We sent login credentials to your email. Use the password from the email to sign in.

Didn't receive the email?
Check your Spam folder
Already have an account? Sign In · Forgot password?

Welcome!

You have successfully signed in.

Don't have an account? Register · Forgot password?

Password Recovery

Enter your email to recover access

Enter a valid email

Link sent

A password reset link has been sent to the specified email. The link is valid for 1 hour.

Didn't receive the email?
Check your Spam folder
Remember your password? Sign In · Register